AAI141 vs AAI143 Yokogawa Analog Input Modules: Isolation, HART and Redundancy Compared

The Yokogawa AAI141 is a 16-channel non-isolated 4–20 mA analog input module, while the AAI143 provides per-channel isolation rated 1500 V AC for one minute. Both share ±16 µA accuracy, 10 ms updates, dual-redundancy support and HART, so the right choice depends on your cabinet wiring, earthing scheme and cable system.
What separates the AAI141 from the AAI143 in isolation architecture?
The core difference is isolation: the AAI143 isolates each channel from the system at 1500 V AC for one minute (500 V AC when the KS1 dedicated cable is used), whereas the AAI141 is non-isolated with a permitted common-mode voltage of only ±1 V, making earthing and wiring discipline decisive.
- AAI143 input-to-system withstand voltage: 1500 V AC for 1 minute, or 500 V AC when the KS1 dedicated cable is used (Yokogawa GS 33K50F60-50E Release 5).
- AAI141 permitted common-mode voltage: within ±1 V, reflecting its non-isolated channel design (Yokogawa GS 33K50F60-50E Release 5).
- Zener barrier connection is not allowed on either module (Yokogawa GS 33K50F60-50E Release 5).
On the isolated module, every input channel is galvanically separated from the system side, which is why the AAI143 suits panels where field cabling of uncertain origin shares a cabinet with control-system electronics. The non-isolated AAI141 instead assumes a cleanly bonded installation, because its channels share a common reference. Neither module may be connected across Zener barriers, so intrinsically safe loops need a separate interface. A base configuration such as the AAI143-S00 isolated input module carries this isolated architecture with the standard non-HART suffix.
The table below collects the head-to-head figures:
| Specification | AAI141 | AAI143 |
|---|---|---|
| Isolation | Non-isolated; common-mode within ±1 V | Isolated per channel from system |
| Input-to-system withstand voltage | Non-isolated design | 1500 V AC for 1 min; 500 V AC with KS1 dedicated cable |
| Channels / signal | 16 channels, 4–20 mA | 16 channels, 4–20 mA |
| Accuracy | ±16 µA | ±16 µA |
| Data update period | 10 ms | 10 ms |
| Permissible input current | 27 mA | 24 mA |
| Transmitter power supply | 14.8 V (20 mA) to 26.4 V (0 mA); limit 27 mA | 19.0 V (20 mA) to 25.5 V (0 mA); limit 25 mA |
| Input impedance (power on) | 400 Ω (20 mA) to 1000 Ω (4 mA) | 270 Ω (20 mA) to 350 Ω (4 mA) |
| Input impedance (power off) | 500 kΩ or more | 500 kΩ or more |
| 2-wire / 4-wire setting | Per channel via setting pins | Per channel via setting pins |
| Temperature drift | ±16 µA/10 °C | ±16 µA/10 °C |
| HART | Supported; ER node needs EB401 firmware rev. 2 or later | Supported |
| Dual redundancy | Supported | Supported |
| Zener barrier use | Not allowed | Not allowed |
| External connections | Pressure-clamp terminals, KS cables, MIL connector cables | Pressure-clamp terminals, MIL connector cables, KS1 dedicated cable |
| Current consumption | 310 mA (5 V) / 450 mA (24 V) | 230 mA (5 V) / 540 mA (24 V) |
| Weight | 0.2 kg | 0.3 kg |
Which transmitter power supply window suits your loop devices?
Transmitter power differs meaningfully: the AAI141 delivers 14.8 V at 20 mA up to 26.4 V at 0 mA with 27 mA current limiting, while the AAI143 supplies a narrower 19.0 V to 25.5 V window with 25 mA limiting, so loops with long cable runs gain more voltage budget from the AAI141.
- AAI141 transmitter power supply: 14.8 V (at 20 mA) to 26.4 V (at 0 mA), current-limited at 27 mA (Yokogawa GS 33K50F60-50E Release 5).
- AAI143 transmitter power supply: 19.0 V (at 20 mA) to 25.5 V (at 0 mA), current-limited at 25 mA (Yokogawa GS 33K50F60-50E Release 5).
- Input impedance, power on: AAI141 400 Ω (20 mA) to 1000 Ω (4 mA); AAI143 270 Ω (20 mA) to 350 Ω (4 mA); power off, 500 kΩ or more for both (Yokogawa GS 33K50F60-50E Release 5).
Loop loading shifts too. With power on, the AAI141 presents 400 Ω at 20 mA, rising to 1000 Ω at 4 mA, whereas the AAI143 presents only 270 Ω at 20 mA to 350 Ω at 4 mA. De-energized, both paths exceed 500 kΩ, so a powered-down module barely loads the loop. Permissible input current is 27 mA on the AAI141 against 24 mA on the AAI143 — a small margin that helps when a transmitter briefly overshoots range.
How do cable systems and external connections differ between the two modules?
The two modules use different cable ecosystems: the AAI141 connects through pressure-clamp terminals, KS cables or MIL connector cables, while the AAI143 uses pressure-clamp terminals, MIL connector cables or the KS1 dedicated cable, so existing cabinet pre-wiring usually dictates which module a retrofit can accept without re-termination.
- AAI141 external connections: pressure-clamp terminals, KS cables, MIL connector cables (Yokogawa GS 33K50F60-50E Release 5).
- AAI143 external connections: pressure-clamp terminals, MIL connector cables, KS1 dedicated cable (Yokogawa GS 33K50F60-50E Release 5).
- /K4A00 suffix: KS Cable Interface Adapter, model ATK4A-00 (Yokogawa GS 33K50F60-50E Release 5).
For KS-cabled cabinets, the /K4A00 suffix specifies the KS Cable Interface Adapter (ATK4A-00), which lets the module family slot into pre-wired harnesses. Two frequently requested examples are the AAI141-H50/K4A00 HART input module for HART-equipped loops and the AAI141-S50/K4A00 16-channel 4–20 mA module for standard service.
How do HART support, suffix codes and node placement shape your order?
Both modules support HART and dual redundancy, but suffix codes define the exact variant: -S is the standard version without HART, -H adds HART, the second digit separates non-explosion-protected (5) from explosion-protected (E) types, and the third digit 3 selects the ISA G3 option with −20 to 70 °C operation.
- HART on the AAI141 mounted on an ER bus node requires EB401 firmware rev. 2 or later (Yokogawa GS 33K50F60-50E Release 5).
- Applicable node units: ESB/ER bus node units ANB10S/D, ANB11S/D and ANR10S/D; FCUs AFV30/40, AFV10 and AFF50 (Yokogawa GS 33K50F60-50E Release 5).
- Current consumption: AAI141 310 mA (5 V)/450 mA (24 V); AAI143 230 mA (5 V)/540 mA (24 V) (Yokogawa GS 33K50F60-50E Release 5).
Physically, both are CENTUM VP FIO analog input modules for ESB bus and ER bus node units — ANB10S/D, ANB11S/D and ANR10S/D — as well as for FCUs such as AFV30/AFV40, AFV10 and AFF50. One HART caveat applies to the AAI141: on an ER bus node, HART communication requires EB401 firmware revision 2 or later. For worked ordering examples, the Yokogawa AAI143 selection guide walks through each suffix position in detail.
Frequently asked questions
Can an AAI143 directly replace an AAI141 in an existing cabinet?
No — the two modules are not treated as direct replacements, because the AAI141 is a 16-channel non-isolated 4–20 mA input with a 14.8–26.4 V transmitter power window, 27 mA permissible input and KS cable connectivity, while the AAI143 is a per-channel isolated input rated 1500 V AC for one minute with a narrower 19.0–25.5 V window and KS1 dedicated cable connectivity. Replacement therefore depends on the cabinet's cable system and the terminal board fitted behind the module. Any further interchangeability details are not disclosed in public documentation, so confirm wiring drawings before ordering.
Is the AAI143 compatible with my existing CENTUM VP node units?
Yes — both modules are CENTUM VP FIO analog input modules that install in ESB bus and ER bus node units (ANB10S/D, ANB11S/D and ANR10S/D) as well as directly in FCUs (AFV30/AFV40, AFV10 and AFF50), and both offer dual redundancy, per-channel two-wire/four-wire setting pins, identical ±16 µA accuracy and 10 ms data updates, so cabinet field wiring rather than system compatibility normally decides between them. One HART caveat concerns the AAI141: on an ER bus node it needs EB401 firmware revision 2 or later. Both can also operate as a redundant pair within the same node unit.
How do I read the suffix code when ordering either module?
Order codes follow the same suffix logic for both modules: the first suffix letter sets HART capability (-S is the standard version without HART, while -H is the HART version), the second digit distinguishes non-explosion-protected (5) from explosion-protected (E) construction, and the third digit selects either the basic type (0) or the ISA G3 compliant type with the −20 to 70 °C temperature option (3). The /K4A00 suffix additionally specifies the KS Cable Interface Adapter (ATK4A-00). Typical orders include the AAI141-H50/K4A00 for a HART loop on KS cabling and the AAI143-S00 as a standard isolated input without HART; for more detail, see our guide's AAI143 suffix codes explained section.
Petroparts Online is an independent distributor of Yokogawa CENTUM VP FIO spare parts, including both analog input modules compared above. Send your existing module part number or node configuration, and our team will cross-check the suffix, cable adapter and redundancy requirements against your application; hard-to-source variants can be traced through our international supplier network.
