Product Overview

The Bently Nevada 330106-05-030-10-02-CN belongs to the 3300 XL Series. This sensor provides reliable vibration and position measurements. The 3300 XL 8 mm Reverse Mount Probe works well in harsh industrial environments. Its PPS tip and stainless steel case ensure long service life.

Technical Specifications

The 330106-05-030-10-02-CN uses a Polyphenylene sulfide (PPS) probe tip. This material offers excellent chemical resistance. The probe case uses AISI 303 or 304 stainless steel (SST). This construction withstands high stress and corrosion.

Electrical Parameters

• Nominal DC Resistance: 7.73 ± 0.50 Ω (Center to Outer Conductor)

• Cable Impedance: 75Ω triaxial design

• Insulation Material: Fluoroethylene propylene (FEP) for standard cable

Mechanical Dimensions

• Thread Size: <b>M10 x 1</b>

• Maximum Thread Engagement: 15 mm

• Weight: 323 g/m (11.4 oz per meter)

• Total Length Option: 1.0 meter (4.9 feet)

• Connector Type: Miniature ClickLoc coaxial connector

Temperature Range

• Standard Probe Operating: -52°C to +177°C (-62°F to +350°F)

• Storage Temperature: Same as operating range

• Low Temperature Warning: Exposure below –34°C (-30°F) may damage the pressure seal

Environmental Tolerance

• Relative Humidity: Less than 3% change in Average Scale Factor (ASF)

• Test Standard: IEC 68-2-3 at 93% humidity for 56 days

• Pressure Seal Material: Viton® O-ring

• Note: Factory does not pressure test probes before shipment

Mechanical Strength

• Tensile Strength (Case to Lead): 330 N (75 lbf)

• Tensile Strength (Lead to Connector): 270 N (60 lbf)

• Optional Armor: Flexible AISI 302 or 304 SST with FEP jacket

Installation Guide

Follow these steps to install the 3300 XL 8 mm Reverse Mount Probe:

1. Clean the mounting hole with a proper thread cleaner.

2. Apply anti-seize compound on the <b>M10 x 1</b> threads if needed.

3. Screw the probe by hand to avoid cross-threading.

4. Use a torque wrench for final tightening. Do not exceed the specified torque.

5. Connect the Miniature ClickLoc connector firmly to the extension cable.

6. Verify the probe gap voltage using a proximitor.

Tip: Keep the probe cable away from high voltage sources. This reduces electrical noise.

Package List

The box contains the following items for 330106-05-030-10-02-CN:

• One 3300 XL 8 mm Reverse Mount Probe (1.0m total length)

• One Miniature ClickLoc coaxial connector (pre-attached)

• One protective plastic cap for the probe tip

• One installation instruction sheet (quick start guide)

Frequently Asked Questions (FAQ)

Q1: What machinery uses the 330106-05-030-10-02-CN probe?
A1: This probe monitors vibration in turbines, compressors, pumps, and fans. The 3300 XL Series works well in rotating machinery.

Q2: Can I extend the cable length of this probe?
A2: Yes. You need a Bently Nevada extension cable. The ClickLoc connector ensures a secure fit with any compatible cable.

Q3: Is the probe tip replaceable if damaged?
A3: No. The probe tip is non-replaceable. You must replace the whole 3300 XL 8 mm Reverse Mount Probe assembly.

Q4: What is the maximum operating temperature for the probe tip?
A4: The standard probe tip works up to +177°C (+350°F). Do not exceed this limit to avoid permanent damage.

Q5: Does humidity affect the probe performance?
A5: Very little. The probe passes IEC 68-2-3 humidity testing. The scale factor changes less than 3% at 93% relative humidity for 56 days.

Compliance and Note

This Bently Nevada 330106-05-030-10-02-CN carries a country-specific approval code "CN". Always follow local safety regulations during installation. Store the probe in a dry place between -52°C and +177°C. Do not pull the cable directly. Pull only the connector or probe body.