Kit Components

The 2300/25_KIT-005-00 includes several key components for immediate use.

Main Components:

• 2300/25 Monitor with SPA outputs – 1 piece

• Velomitor sensor (330500) – 1 piece

• 17 ft. (5.2 m) cable (9571) – 1 piece

• 6 ft. (1.8 m) shielded Ethernet cable – 1 piece

Housing Options (varies by order):

• Housing Kit 105M6193-01 for nonhazardous areas (fiberglass)

• Housing Kit 105M6193-03 for hazardous areas (stainless steel)

Housing Dimensions

The housing included with 2300/25_KIT-005-00 measures 18.03 x 15.04 x 6.3 inches. This provides ample space for the monitor and wiring. Fiberglass housing suits general industrial environments. Stainless steel housing is for hazardous area installations.

Monitor Technical Specifications (2300/25)

The 2300/25 monitor inside this kit operates on 18 to 36V DC input. Maximum power consumption is only 7.5W. This monitor features independent 24-bit ADCs on all input channels. Measurement accuracy reaches ±1% of the full scale range. The 2300/25 supports Bently transducers or custom 2/3 wire sensors.

Input Channel Types

The 2300/25 monitor offers flexible configuration for various measurements.

ICP Accelerometers:

• Bandpass filter: 0.2 Hz to 20 kHz

• Scale factor range: 5 to 1000 mV/g

• Full scale range: 2 to 80 g peak

• Current sink source: 3.3 mA ± 5%

• Open circuit voltage: -21 to -24 Vdc

Velocity (Velomitor compatible):

• Bandpass filter: 0.2 Hz to 20 kHz

• Scale factor range: 5 to 1000 mV/in/s

• Full scale range: 0 to 50 in/s peak

Radial Vibration:

• Bandpass filter: 0.2 Hz to 20 kHz

• Scale factor range: 5 to 1000 mV/mil

• Full scale range: 0 to 160 mil peak-peak

Thrust Channel:

• Scale factor range: 5 to 1000 mV/mil

Speed and Keyphasor Inputs

The 2300/25 monitor supports Keyphasor transducers for speed measurement. Threshold voltage resolution is 0.1 Vdc. RPM range for proximity transducers reaches 1 to 120,000. Magnetic pickup inputs adapt to sensor 284947 output. RPM range for magnetic pickups is 200 to 120,000.

Proximity Interfaces

The 2300/25 includes a proximity transducer interface. Supply voltage ranges from -22.8 to -25.2 Vdc. Maximum rated current is 15 mA. Input impedance is 10 kΩ for 3-wire voltage mode. The proximity switch interface supplies -10 to -24 Vdc. Lower not OK limit is -2.75 ±0.05 V. RPM range for this interface goes to 60,000.

Velomitor Sensor (330500)

The 2300/25_KIT-005-00 includes one Velomitor sensor model 330500. This sensor measures absolute casing vibration velocity. It requires no external signal conditioner. The sensor connects using the included 17 ft. (5.2 m) cable 9571. This Velomitor is compatible with the 2300/25 monitor’s velocity channel settings.

Output Specifications

Buffered Outputs

Three buffered outputs are available on the 2300/25 monitor. These connect through BNC connectors on the front panel. Two outputs carry vibration signals. One output provides speed signal.

Relay Outputs

The 2300/25 monitor has two dry-contact relay outputs. Relays can be normally energized or de-energized. Contact life reaches 100,000 cycles at 5 amps, 250 Vac. Insulation resistance is 1000 MΩ minimum at 500 Vdc. Maximum switched voltage is 250 Vac or 250 Vdc. Breaking current reaches 6 A at 250 Vac or 6 A at 24 Vdc.

SPA Outputs

SPA output specifications for the 2300/25 monitor include an input signal range of high AC at 8 Vpp. Low AC range is 1.6 Vpp. DC GAP range is 0 to -20 Vdc. Accuracy for high and low AC is ±1% of full scale at 100 Hz. DC GAP accuracy is ±0.5 V. Frequency response spans 10 Hz to 3000 Hz with ±5% tolerance.

Environmental Limits

The 2300/25_KIT-005-00 system operates in harsh industrial environments. Operating temperature ranges from -30°C to +65°C (-22°F to +149°F). Storage temperature goes from -40°C to +85°C (-40°F to +185°F). Humidity tolerance is up to 95% non-condensing. Vibration limitation is 3 g. The real time clock battery lasts 38 years when powered at 50°C. Unpowered battery life reaches 12 years at the same temperature.

Communications and Data Storage

The 2300/25 monitor uses Ethernet for remote communication. It supports 10Base-T and 100Base-TX standards. The connection conforms to IEEE802.3 using an RJ-45 connector. Maximum cable length is 100 meters (328 feet). In case of network disruption, this monitor stores at least 5 alarm data captures. This feature requires System 1 Evolution 21.1 or newer. Firmware release 3.2 or newer is also necessary for the 2300/25.

Trend Measurement Intervals

Pre-Event Data:

• 10 minutes at 1 second intervals

• 20 seconds at 100 millisecond intervals

Post-Event Data:

• 10 seconds at 100 millisecond intervals

• 1 minute at 1 second intervals

Spectrum and Waveform Intervals

Pre-Event Data:

• 2.5 minutes at 10 second intervals

Post-Event Data:

• 1 minute at 10 second intervals

Status LEDs and Display

The 2300/25 monitor includes multiple status indicators. The OK LED shows when the monitor operates properly. Protection fault LED indicates hardware issues affecting alarms. User inhibit LED shows intentionally inhibited alarms or relays. Bypass LED indicates user initiated bypass action. Relay status LED shows if relays are activated. TX/RX LED indicates Ethernet communication status. Channel alarm status includes an Alert LED and a Danger LED. The LCD display allows viewing speed, vibration values, setpoints, and configuration data.

Installation Guidelines

Mount the 2300/25 monitor using panel mount or DIN rail methods. A DIN rail adapter is included with the monitor. Install the Velomitor sensor (330500) on the machine casing. Use the 9571 cable to connect the sensor to the 2300/25 monitor. Place the housing in a suitable location near the monitored machine. Ensure power supply provides 18 to 36V DC stable voltage. Connect the COM terminal to chassis ground using the jumper. Keep Ethernet cable length under 100 meters for reliable communication.

Kit Package Contents

The 2300/25_KIT-005-00 includes the following items:

• 2300/25 Monitor with SPA outputs – 1 piece

• Velomitor sensor (330500) – 1 piece

• 17 ft. (5.2 m) cable (9571) – 1 piece

• 6 ft. (1.8 m) shielded Ethernet cable – 1 piece

• Housing Kit (fiberglass or stainless steel) – 1 piece

• DIN rail mount assembly – 1 piece

• Product manual – 1 copy

• Monitor configuration software CD – 1 copy

Note: Keyphasor sensor and 24V DC power supply are not included. You must purchase these separately.

Frequently Asked Questions (FAQ)

1. What is the difference between housing options in this kit?
The 2300/25_KIT-005-00 with 105M6193-01 is fiberglass for nonhazardous areas. The 105M6193-03 version is stainless steel for hazardous area use.

2. Does this kit include the Keyphasor sensor for speed measurement?
No, the 2300/25_KIT-005-00 excludes the Keyphasor sensor. You must order it separately if speed reference is needed.

3. What power supply do I need for this monitoring system?
You need an external 24V DC power supply. The 2300/25 monitor accepts 18 to 36V DC input. Maximum power draw is 7.5 watts.

4. Can I add more sensors to the 2300/25 monitor later?
Yes, the 2300/25 monitor supports multiple channel types. You can add accelerometers or proximity probes as needed. The monitor has inputs for several configurations.

5. What is the maximum cable length for the Velomitor sensor?
The 2300/25_KIT-005-00 includes a 17 ft. (5.2 m) cable. You can extend this with proper shielded cable, but keep total length under 300 meters for signal integrity.

Physical Dimensions (Monitor Only)

• Width: 127 mm (5 inches)

• Depth: 127 mm (5 inches)

• Height: 76.2 mm (3 inches)

• Weight: 1.03 kg (2.26 lbs)

• Mounting: Panel mount or DIN rail (adapter included)

Housing Dimensions

• Width: 18.03 inches

• Depth: 15.04 inches

• Height: 6.3 inches

This 2300/25_KIT-005-00 condition monitoring kit delivers complete vibration protection. Order now to simplify your machine monitoring installation.