Product Overview: Bently Nevada 2300/20_KIT-005-00

The 2300/20_KIT-005-00 provides standalone machinery protection in one package. This kit contains everything needed for basic vibration monitoring. The 2300/20_KIT-005-00 includes a 2300/20 monitor with configuration 005. It comes with one Velomitor sensor and a 17 foot shielded cable. The kit also includes a protective housing for the monitor.

Kit Contents

The 2300/20_KIT-005-00 arrives as a complete ready-to-install system. The main monitor is the 2300/20 device with approvals option 00. One Velomitor sensor (model 330500) is included for vibration pickup. A 6 foot shielded Ethernet cable connects the monitor to your network.

Complete Package Includes:

• (1) 2300/20 Monitor

• (1) Velomitor sensor (330500)

• (1) 17 ft (5.2 m) sensor cable (9571)

• (1) 6 ft (1.8 m) shielded Ethernet cable

• (1) Housing kit (105M6193-01 or 105M6193-03)

The 2300/20_KIT-005-00 includes a choice of housing. Non-hazardous areas use fiberglass housing 105M6193-01. Hazardous areas receive stainless steel housing 105M6193-03. Each housing measures 18.03 x 15.04 x 6.3 inches. The monitor mounts inside using either panel or DIN rail adapters.

Technical Specifications

The 2300/20_KIT-005-00 monitor accepts multiple channel types. It supports ICP accelerometers with configurable bandpass filters. The filter range spans from 0.2 Hz to 20 kHz. Scale factor range is 5 to 1000 mV/g for accelerometers. Full scale range reaches 2 to 80 g peak.

• Power Input: 18 to 36 Vdc, max 7.5 W

• Accelerometer Scale Factor: 5 to 1000 mV/g

• Velocity Scale Factor: 5 to 1000 mV/in/s

• Radial Vibration Scale Factor: 5 to 1000 mV/mil

• Thrust Channel Scale Factor: 5 to 1000 mV/mil

• Accuracy: ±1% of full scale range

The 2300/20_KIT-005-00 uses independent 24-bit ADCs on all input channels. This provides high resolution for precise vibration measurements. The monitor supports Bently Nevada transducers directly. It also accepts 2-wire or 3-wire custom transducers.

Speed and Keyphasor Inputs

The 2300/20_KIT-005-00 includes a dedicated speed measurement channel. Keyphasor transducers support multiple events per revolution. The threshold voltage resolution is 0.1 Vdc. RPM range for proximity and Keyphasor inputs is 1 to 120,000.

Speed Input Specifications:

• Keyphasor RPM Range: 1 to 120,000 RPM

• Proximity Switch RPM Range: 1 to 60,000 RPM

• Magnetic Pickup RPM Range: 200 to 120,000 RPM

• Threshold Resolution: 0.1 Vdc

• Maximum Frequency Input: 20 kHz

The 2300/20_KIT-005-00 also accepts magnetic pickup sensors. The input voltage adapts to sensor 284947 output automatically. This flexibility allows connection to existing installed sensors. The monitor can use a single sensor for both speed and vibration.

Channel Configuration Options

The 2300/20_KIT-005-00 offers extensive channel configurability. Each channel has independent bandpass filter settings. The upper OK limit ranges from -0.25 to -22 Vdc. The lower OK limit also ranges from -0.25 to -22 Vdc.

Configurable Channel Types:

• Process Variable Channel: Default on for most units

• Temperature Channel: Hardware configurable

• Radial Vibration: 0 to 160 mil peak-peak range

• Velocity: 0 to 50 in/s peak range

• Accelerometer: 2 to 80 g peak range

The 2300/20_KIT-005-00 includes proximity transducer interface features. Supply voltage is -22.8 to -25.2 Vdc for proximity probes. Maximum rated current is 15 mA per channel. Short circuit current limits from 15.1 to 23.6 mA. Input impedance is 10 kΩ for 3-wire voltage mode.

Output Capabilities

The 2300/20_KIT-005-00 provides multiple output options for integration. Three buffered outputs are available through BNC connectors. Two outputs carry vibration signals for external analysis. One output provides speed signal for tachometer use.

Output Specifications:

• Buffered Outputs: 3 BNC connectors (2 vibration, 1 speed)

• 4-20mA Outputs: 2 channels with internal loop power

• Load Resistance: 0 to 600 Ω

• Resolution: 0.3662 µA

• Update Rate: 100 ms

• Voltage Compliance: 0 to +12 Vdc

The 2300/20_KIT-005-00 includes two dry-contact relays. These relays can be normally energized or de-energized. Contact life is 100,000 cycles at 5 amps, 250 Vac. Maximum switched power is 1500 VA AC or 150 Watts DC. Hazardous area ratings have lower voltage and current limits.

Environmental Specifications

The 2300/20_KIT-005-00 operates in extreme industrial conditions. Operating temperature ranges from -30°C to +65°C. Storage temperature spans -40°C to +85°C. Humidity tolerance reaches 95 percent without condensation.

• Operating Temperature: -30°C to +65°C (-22°F to +149°F)

• Storage Temperature: -40°C to +85°C (-40°F to +185°F)

• Humidity: Up to 95%, non-condensing

• Vibration Limitation: 3 g maximum

• Enclosure Rating: Depends on selected housing

The 2300/20_KIT-005-00 has a real-time clock with battery backup. Powered battery life is 38 years at 50°C. Unpowered battery life is 12 years at the same temperature. This ensures accurate time stamps during power outages.

Data Capture and Storage

The 2300/20_KIT-005-00 stores pre-event and post-event data. For trend measurements, pre-event data captures 10 minutes at 1 second intervals. It also captures 20 seconds at 100 millisecond intervals. Post-event trend data captures 10 seconds at 100 millisecond intervals.

Data Capture Capabilities:

• Trend Pre-Event: 10 min @ 1 sec, 20 sec @ 100 ms

• Trend Post-Event: 10 sec @ 100 ms, 1 min @ 1 sec

• Spectrum Pre-Event: 2.5 min @ 10 sec

• Spectrum Post-Event: 1 min @ 10 sec

• Alarm Storage: 5 captures minimum during network disruption

The 2300/20_KIT-005-00 requires System 1 Evolution 21.1 or newer. Firmware release 3.2 or newer is also required for full storage. This ensures data is not lost during network interruptions.

Communications Interface

The 2300/20_KIT-005-00 uses standard Ethernet for connectivity. The port supports 10Base-T and 100Base-TX speeds. It conforms fully to IEEE802.3 specifications. The RJ-45 connector accepts standard Ethernet cabling.

• Protocol: Ethernet TCP/IP

• Speed: 10/100 Mbit/s auto-negotiation

• Cable Type: Shielded or unshielded twisted pair

• Max Cable Length: 100 meters (328 feet)

• Configuration: Via web browser or System 1 software

The 2300/20_KIT-005-00 includes status LEDs on the front panel. An OK LED indicates the monitor is operating properly. Protection fault LED shows hardware faults affecting alarms. User inhibit LED shows intentionally inhibited alarms. Relay status LEDs indicate relay activation states.

Front Panel Interface

The 2300/20_KIT-005-00 has an LCD display for local viewing. Users can see machine speed and vibration measurement values. Setpoints and configuration information are also viewable. Three buried buttons provide access to monitor functions.

Button Functions on the 2300/20_KIT-005-00:

• Display Info: Shows monitor information

• LCD Contrast: Adjusts display brightness

• Reset Settings: Returns to factory defaults

• Reset Latched Alarm: External button function

• Bypass Action: User initiated bypass

The 2300/20_KIT-005-00 includes contact inputs for external control. Configuration lock prevents unauthorized changes. Latched alarm and relay reset functions are supported. Monitor bypass activation requires 0 to 10 kΩ. De-activation requires 150 kΩ to infinite resistance.

Physical Dimensions

The 2300/20_KIT-005-00 monitor has a compact footprint. Width is 127 mm (5 inches). Depth is also 127 mm (5 inches). Height is 76.2 mm (3 inches). Total weight is 1.03 kg (2.26 lbs).

• Monitor Dimensions: 127 x 127 x 76.2 mm

• Monitor Weight: 1.03 kg

• Housing Dimensions: 18.03 x 15.04 x 6.3 inches

• Mounting Options: Panel mount or DIN rail

• DIN Rail Adapter: Included with kit

The 2300/20_KIT-005-00 includes a DIN rail adapter in the package. This allows flexible installation in existing cabinets. Panel mounting is also supported with the same adapter. The housing protects the monitor in harsh environments.

Installation Guidelines

Mount the housing for the 2300/20_KIT-005-00 on a solid surface. Use the included fiberglass or stainless steel enclosure. Install the 2300/20 monitor inside the housing securely. Connect the Velomitor sensor using the 17 foot cable.

Key Installation Points:

• Sensor Mounting: Use supplied 330500 Velomitor

• Cable Routing: Keep sensor cable separate from power

• Power Supply: 24 Vdc required, not included

• Grounding: Use jumper between COM and chassis GND

• Ethernet: Connect to RJ-45 for configuration

The 2300/20_KIT-005-00 does not include the 24 Vdc power supply. Users must provide a suitable Class 2 power source. The Keyphasor sensor is also excluded from this kit. These items must be purchased separately.

Package Contents

Your purchase of the 2300/20_KIT-005-00 includes:

• (1) 2300/20 Monitor with configuration 005

• (1) 330500 Velomitor sensor

• (1) 9571 sensor cable (5.2 meters / 17 feet)

• (1) Shielded Ethernet cable (1.8 meters / 6 feet)

• (1) Housing kit (fiberglass or stainless steel)

• (1) DIN rail mounting adapter

Frequently Asked Questions (FAQ)

Q: What sensors work with the 2300/20_KIT-005-00?
A: The 2300/20_KIT-005-00 works with ICP accelerometers and Velomitors. It also accepts Bently Nevada proximity probes and magnetic pickups.

Q: Does the 2300/20_KIT-005-00 include a power supply?
A: No, the 2300/20_KIT-005-00 requires a separate 24 Vdc power supply. The monitor draws a maximum of 7.5 Watts.

Q: What is the maximum RPM for speed measurement?
A: The 2300/20_KIT-005-00 measures up to 120,000 RPM. This applies to proximity and Keyphasor transducer inputs.

Q: Can the 2300/20_KIT-005-00 be used in hazardous areas?
A: Yes, the 2300/20_KIT-005-00 offers stainless steel housing option 105M6193-03. This housing is certified for hazardous area installation.

Q: How many 4-20mA outputs does the 2300/20_KIT-005-00 provide?
A: The 2300/20_KIT-005-00 provides two 4-20mA outputs. Each output has internal loop power (no external supply needed).