Product Overview

The HIMA X-COM01 is a versatile communication module for HIMax safety systems. This module provides four RJ-45 ports and one 9-pin D-Sub connector. It supports up to six different protocols for flexible integration. The X-COM01 runs safeethernet and standard communication protocols. You get auto negotiation and auto crossover on all Ethernet ports.

Technical Specifications

General Power Data

• Supply Voltage: 24 VDC with -15 % to +20 % tolerance.

• Ripple (rP): ≤ 5 %, SELV, PELV compliant.

• Current Input Minimum: 0.25 A.

• Current Input Maximum: 0.46 A.

• Protection Class: Class III per IEC/EN 61131-2.

Environmental Limits

• Operating Temperature: 0 °C to +60 °C.

• Storage Temperature: -40 °C to +85 °C.

• Relative Humidity: Max 95 %, non-condensing.

• Type of Protection: IP20.

• Pollution Degree: Degree II per IEC/EN 61131-2.

• Altitude: Below 2000 metres.

Physical Characteristics

• Dimensions (H x W x D): 310 mm x 29.2 mm x 230 mm.

• Weight: Approximately 1.3 kg.

• Housing Type: Standard IP20 rated enclosure.

• Module Width: Slim single-wide format for HIMax racks.

Ethernet Communication Ports

• Number of Ports: 4 Ethernet ports.

• Transfer Standard: 10BASE-T and 100BASE-Tx.

• Duplex Mode: Half and full duplex supported.

• Auto Negotiation: Yes, enabled by default.

• Auto Crossover: Yes, no special cables needed.

• Connection Type: RJ-45 socket.

• IP Address: Freely configurable by user.

• Subnet Mask: Freely configurable by user.

• Supported Protocols: safeethernet and standard protocols.

Fieldbus Interfaces

• Number of Interfaces: 2 fieldbus interfaces.

• Transfer Standard: Depends on each fieldbus submodule.

• Connection Type: D-Sub connector with 9 poles.

• Protocol Limit: One protocol per fieldbus interface only.

• Submodule Requirement: Fieldbus submodules must be ordered separately.

• Supported Protocols: Refer to Communication Manual (HI 801 101 E).

Installation Guide

Follow these steps to install the HIMA X-COM01 correctly. First, specify required fieldbus submodules when ordering the module. Second, insert the X-COM01 into a free slot in your HIMax rack. Third, connect the 24 VDC supply voltage with proper SELV/PELV isolation. Fourth, attach Ethernet cables to the four RJ-45 ports as needed. Fifth, connect fieldbus devices to the 9-pin D-Sub connectors. Sixth, configure IP addresses and subnet masks using HIMax engineering tools. Seventh, verify auto negotiation establishes correct link speeds. Finally, test each protocol channel before system startup.

Package Contents

• 1 x HIMA X-COM01 communication module.

• 1 x Front panel with 4 x RJ-45 ports and 1 x D-Sub connector.

• Note: Fieldbus submodules must be ordered separately.

• Note: No Ethernet or D-Sub cables included.

• Note: No configuration software or documentation CD included.

Frequently Asked Questions (FAQ)

Q1: How many protocols can the HIMA X-COM01 run simultaneously?
A: The X-COM01 supports up to six different protocols in total. However, each fieldbus interface runs only one protocol at a time. The Ethernet ports can run safeethernet alongside other standard protocols.

Q2: Do I need to order fieldbus submodules separately for the HIMA X-COM01?
A: Yes, you must specify required fieldbus submodules when ordering the module. The submodules activate the fieldbus interfaces and define the transfer standard. Without submodules, the D-Sub connectors will not function.

Q3: What is the auto crossover feature on the X-COM01 Ethernet ports?
A: Auto crossover allows you to use straight or crossover Ethernet cables without worry. The X-COM01 detects the cable type and adjusts automatically. This simplifies installation and reduces cabling errors.

Q4: Can I use the HIMA X-COM01 at temperatures above 60 °C?
A: The maximum operating temperature is 60 °C for reliable safety communication. Storage can reach 85 °C but operation above 60 °C is not permitted. Install the module in a ventilated cabinet away from heat sources.

Q5: What does the IP20 protection rating mean for the X-COM01?
A: IP20 means the module is protected against solid objects over 12.5 mm. It offers no protection against water or dust ingress. You must install this HIMA X-COM01 inside an enclosure rated for your environment.