Product Overview of Bently Nevada 9200-06-02-01-00

The Bently Nevada 9200-06-02-01-00 is a two-wire velocity seismoprobe transducer. This sensor measures absolute casing vibration on industrial rotating machinery. The 9200-06-02-01-00 delivers reliable data for machine protection systems. It works well on high-speed turbines, compressors, pumps, and fans. The 10 Hz minimum frequency suits applications above 600 cpm. The side mount connector allows easy access in tight spaces.

Key Technical Specifications

Sensitivity: 20 mV/mm/s (500 mV/in/s) with ±5% tolerance. This rating applies when properly terminated and oriented at the calibration angle.

Velocity Range: 25 mm/s (1 in/s) at +22°C casing vibration at 100 Hz with a 10 kΩ load.

Dynamic Operating Range: 2.54 mm (0.100 in) peak to peak maximum displacement.

Coil Resistance: 1.25 kΩ ±5%. Locked coil inductance measures 125 mH typical.

Calibration Load: 10 kΩ between Terminal A and Terminal B. Output measurement occurs across pins A and B.

Sensitivity Temperature Coefficient: 0.2% per degree Celsius for stable readings across temperature changes.

Operating and Storage Temperature: -29°C to +121°C (-20°F to +250°F) for the 9200 series.

Environmental Protection: Dust and moisture resistant construction. Relative humidity tolerance reaches 95% noncondensing.

Housing Material: Case uses anodized aluminum A204. Gasket material is neoprene for reliable sealing.

Dimensions and Weight: Height measures 102 mm (4 inches) typical. Diameter is 41 mm (1.6 inches) typical. Weight equals 300 grams (10.5 ounces).

Ordering Information Breakdown

The Bently Nevada 9200-06-02-01-00 includes these factory options:

• Transducer Mounting Angle/Minimum Operating Frequency Option 06: 0 ±100 degrees, 10 Hz (600 cpm) minimum operating frequency.
• Connector Option 02: Side mount connector with no integral cable.
• Mounting Base Option 01: Circular base with 1/4-20 UNC stud.
• Agency Approval Option 00: No approvals required for non-hazardous installations.

Installation Guidelines

Mount the 9200-06-02-01-00 directly on the machine casing surface. Use the 1/4-20 UNC stud on the circular base. Ensure the mounting surface is clean, flat, and free of paint. Orient the transducer vertically at the 0 degree angle. Connect your field cable to the side mount connector. Use a 10 kΩ termination load between Terminal A and Terminal B. Secure the connector cover to prevent moisture ingress. Route signal wires away from high voltage cables. Verify proper grounding before connecting to the monitor. Do not exceed the maximum displacement of 2.54 mm peak to peak.

Package Contents (No certificates, No warranty clauses, No courier info)

• 1 x Bently Nevada 9200-06-02-01-00 velocity transducer
• 1 x side mount connector (no cable included)
• 1 x circular mounting base with 1/4-20 UNC stud
• 1 x neoprene gasket for sealing
• 1 x connector protective cap
• 1 x installation instruction sheet

Frequently Asked Questions (FAQ)

1. What is the minimum operating frequency of the 9200-06-02-01-00?

The Bently Nevada 9200-06-02-01-00 has a minimum operating frequency of 10 Hz (600 cpm) with a 0 ±100 degree mounting angle.

2. Why choose the side mount connector option over other connectors?

Side mount connector on the 9200-06-02-01-00 saves vertical space and allows installation in tight enclosures where top mount connectors cannot fit.

3. Does this transducer come with a cable attached?

No, the connector option 02 provides a side mount connector without cable. You must supply and attach your own field cable.

4. What termination load does this sensor require?

You need a 10 kΩ load between Terminal A and Terminal B for proper sensitivity calibration.

5. Can this transducer work in hazardous area locations?

No, this model has agency approval option 00 with no certifications. Use it only in non-hazardous environments.

Application Scenarios

The Bently Nevada 9200-06-02-01-00 excels in high-speed rotating machinery monitoring with space constraints. Power plants use it on gas turbines and steam turbine high-pressure sections. Refineries install these sensors on centrifugal compressors and high-speed pumps. The 10 Hz minimum frequency filters out unwanted low frequency noise. This feature improves signal clarity on machines running above 600 rpm. The side mount connector allows installation where vertical clearance is limited. Petrochemical facilities monitor cracked gas compressors with this transducer. Air separation plants use it on turboexpanders and high-speed blowers.

Side Mount Connector Advantages

The side mount connector on the 9200-06-02-01-00 offers distinct benefits. This design reduces the overall height of the installed transducer. You can fit the sensor into shallow junction boxes or tight machine casings. The connector faces sideways for easy cable attachment. Maintenance teams can disconnect the cable without removing the transducer. This feature simplifies sensor testing and replacement. The side mount design also reduces stress on the cable connection point.

Frequency Response Characteristics

The 10 Hz minimum operating frequency of the 9200-06-02-01-00 provides distinct advantages. This transducer rejects vibration signals below 600 cpm. Low frequency noise from structural movement does not affect readings. The sensor focuses on machine-related vibration frequencies. This characteristic improves overall measurement accuracy. For machines operating above 600 rpm, this transducer delivers cleaner data. The 0 ±100 degree mounting angle allows flexible orientation within 100 degrees of vertical.

Environmental Robustness & Compliance

This 9200-06-02-01-00 transducer withstands dusty industrial environments. The anodized aluminum case resists corrosion from moisture and mild chemicals. Neoprene gaskets prevent dust and water ingress. Relative humidity up to 95% noncondensing does not affect operation. The sensitivity temperature coefficient of 0.2%/°C ensures stable readings across the full -29°C to +121°C range. The side mount connector provides a sealed connection point for field wiring. This model carries no hazardous area approvals, making it suitable for general purpose use only.

Compatibility Information

The Bently Nevada 9200-06-02-01-00 works with most Bently Nevada monitoring systems. Use it with 1900/65A, 3500, and 2300 series monitors. The 20 mV/mm/s output matches standard velocity input cards. The 10 kΩ termination load requirement matches Bently Nevada barrier and monitor inputs. The side mount connector accepts standard field wiring. For legacy systems, verify the input impedance before connecting. This transducer also works with third party monitors that accept 20 mV/mm/s velocity inputs with 10 kΩ loading.

Selection Guide for 9200 Series Connector Options

Choose the 9200-06-02-01-00 when vertical space is limited. The side mount connector reduces installed height significantly. Select this option for mounting inside shallow junction boxes. Use it when the transducer must fit between machine casing and guard. For applications requiring a pre-attached cable, choose connector option 50. For top mount terminal block access, choose connector option 05. The side mount option gives you the flexibility to use your own cable length.

Conclusion

The Bently Nevada 9200-06-02-01-00 delivers accurate casing velocity measurements for high-speed machine monitoring. Its 10 Hz minimum frequency rejects low frequency noise effectively. The side mount connector saves vertical space and simplifies cable attachment. For reliable vibration monitoring on rotating machinery above 600 rpm with space constraints, this transducer offers an excellent solution.

Note: This product is new and original in factory packing. For bulk pricing or expedited availability, please contact our sales team.